Hotline: 0984.843.683 Email: info@ttech.vn  Zalo: 0984.843.683

Flow Meter - Style (Flowmeters) 406010/001-406-82 JUMO

Mã sản phẩm: 406010/001-406-82
Sử dụng cho Model:
Hãng SX: Jumo
Xuất xứ
Bảo hành
Tình trạng

Tình trạng: Còn hàng

Đặt hàng
The flow rate transmitter is equipped with a magnetic inductive sensor (MID). Standardized fittings ensure simple installation of the transmitter into DN15 to DN400 pipes/tubes (see data sheet 40.6090).

Liên Hệ Hỗ Trợ

    • SĐT: 0984 843 683

    • Mail: info@ttech.vn

      • Zalo: 0984.843.683

Thông tin sản phẩm

Features


For pressures up to PN 16 and temperatures up to 150°C
Output signal 4...20 mA
Stainless steel sensor
No moving parts
Simple installation
Simple mounting.
Fittings for sensors according to data sheets 406010 and 406020
Large selection of process connections DN 15 to DN 400
Available in plastic or stainless steel
For neutral, aggressive, or contaminated liquids


Specification:

Operating Conditions
Measurement medium Water or other conductive liquids
Minimum conductivity:20 μS/cm
Medium temperature In combination with a PVC fitting: 0 to +50°C
In combination with a PE fitting: 0 to +70°C
In combination with a PP fitting: 0 to +80°C
In combination with a stainless steel fitting:-15 to +150°C
Ambient temperature -10 to +60°C operating temperature
-20 to +60°C storage temperature
Tube diameter For diameters DN15 to DN 400.
Only in combination with fittings as per Data Sheet 406090.
System pressure In combination with a PVC or PE fitting:
JUMO_406010_MID_flow_rate_transmitter_System_pressure
Minimum inlet and
outlet distances
See illustrations on page 5/5
Relative humidity < 80%, non-condensing
Enclosure protection IP65
EMC EN 50081-1, EN 61000-6-2
Safety EN 61010-1
Vibration EN 60068-2-6
Impact EN 60068-2-27
Measuring range
Flow speed 0.2 to 10 m/s
Accuracy
(With a flow speed
of from 1 to 10 m/s
and a medium
temperature in the range
from -15 to 70°C)
With standard K factor: ≤ ± 4% of measured value
After teach-in: ≤ ± 2% of measured value
Linearity ≤ ± 1% of measured value + 0.1% of measurement range end
Repeatability ≤ ± 0.25% of measured value
Materials
Housing, cover, nut PPA
Screws, seal, cable gland Sensor: stainless steel, EPDM, PA
Parts in contact with
medium
Sensor: stainless steel 1.4404/316L, FKM, PEEK
Fitting: see data sheet 406090
Electrical data
Power supply voltage DC 18 to 36 V, reverse polarity protected
Power consumption ≤ 220 mA
Output Current: 4 to 20 mA, three wires
             Loop resistance: max. 1100 Ω at 36 V DC or max. 330 Ω at 18 V DC
Frequency pulse: 0 to 240 Hz
                          Clock ratio: 50%, ≤ 100 mA, protected against short circuit and reverse polarity
Relay: 3 A, 250 VAC, changeover contact
Alarm: when exceeding scale value: 22 mA or 256 Hz
           Device error: 22 mA or 0 Hz
Cable gland M20 x 1.5
Series terminals for lines with cross-section up to 0.75 mm2


Bình luận